How Is Water Horse Power Calculated?
WHP = HQ / 3960 Where H is the change in pressure measured in height of water in feet and Q is the water flow rate in gallons per minute. This equation was derived knowing that one horse- power is equal to 550 ft-lb/s.
How much water can a 10 HP pump?
motor pumps out water from a well of depth 20m and fills a water tank of volume 22380 litres at a height of 10m from the ground.
How much water can a 3 HP pump move?
4 – 43 GPM
Number of submersible well pump stages determine pump lift capacity
| Table of Submersible Pump Stages vs HP vs Total Dynamic Head vs. GPM Flow Rate Capacity | ||
|---|---|---|
| Water Pump HP | Nr. of Pump Stages | GPM Flow Rate Capacity |
| 2 HP | 14 | 4 – 42 GPM (varies by TDH) |
| 3 HP | 19 | 4 – 43 GPM (varies by TDH) |
| 5 HP | 28 | 4 – 43 GPM (varies by TDH) |
What is water horse power?
Water horsepower is the minimum power that is required to move the water (Figure 2). In other words, it is the power that the pump would require if the pump were 100% efficient. The water horsepower can be determined if the flow rate of the water and the force (pressure) required to produce that flow are known.
How much water can a 1.5 HP pump?
1.5 hp horizontal centrifugal pump has maximum flow 4.9m3/h (21.6 gpm), maximum head 29m (95ft) and same diameter of inlet and outlet 25mm (1 inch).
How calculate HP pump capacity?
To calculate the hydraulic power of a pump: Multiply the discharge Q with the differential head H . Multiply the product with the density of the fluid and the acceleration due to the gravity constant.
What is the output of 1 HP water pump?
Output Capacity : 600-2400 LPH.
What is the capacity of 5 HP pump?
5 HP Single Phase 5hp Submersible Pump, Capacity: 600 To 3600 Lpm.
What is the capacity of 1 hp water pump?
Specifications power rating: 1 HP; head: 3 to 32 meters; capacity: 3100 to 500 LPH. Usha: The smooth water supply to overhead tanks in buildings, hotels, and restaurants is ensured by the high suction capacity of these pumps.
What is the capacity of 2 hp water pump?
2 hp Single Phase Submersible Pump, Maximum Discharge Flow: 100-500 LPM.
Is 1hp the power of 1 horse?
Power of a horse
Although it may seem safe to assume that one horsepower is the output a horse is capable of creating at any one time, that is incorrect. In fact, the maximum output of a horse can be up to 15 horsepower, and the maximum output of a human is a bit more than a single horsepower.
How high can a 0.5 HP pump lift water?
Pump: Their pumps are 10 stage pumps with their 0.5HP water pump capacity of water-lifting is up to 215 feet.
What is 1 horse power mean?
horsepower, the common unit of power; i.e., the rate at which work is done. In the British Imperial System, one horsepower equals 33,000 foot-pounds of work per minute—that is, the power necessary to lift a total mass of 33,000 pounds one foot in one minute.
What is the flow rate of a 2hp pump?
2 hp vertical centrifugal pump adopts single stage stainless steel impeller, with maximum flow 5.2m3/h (22.9 gpm), maximum head 33m (108ft), same diameter of inlet and outlet 25mm (1 inch), optional input voltage 3 phase AC 220V/240V/380V/415V/480V and optional input frequency 50Hz/60Hz.
What does 1 hp pump mean?
A power level of 1 hp is approximately equivalent to 746 watts (W) or 0.746 kilowatts (kW). To convert from horsepower to watts, multiply by 746.
How do I choose a water pump size?
The most important factors to consider when sizing a water pump come down to GPM/PSI ratings, inlet/outlet size for water and hoses, how high you’ll need to pump the water (measured in vertical feet), referred to as total head lift, and how far you’ll need to pump the water horizontally.
How is hp value calculated?
The equation to calculate horsepower is simple: Horsepower = Torque x RPM / 5,252.
How is hp load calculated?
Horsepower(hp)= Voltage x Amperage x % EFF x power factor x 1.73/746.
What is the formula for pump power?
Pumping power is calculated as the volume of the fluid per unit time (flow capacity) times the density of the fluid times the gravitational constant times the pumping head (vertical distance to be pumped). Pumping energy is simply power multiplied across time. 100kW of power for one hour is 100kWh of energy.
What is the flow rate of 1.5 hp pump?
Flow rates: These 1.5 HP Water pumps’ flow rates are 1830 – 425 lph.
How many liters per minute of water does a 1.5 hp pump pump?
Head Range : 85 to 118 feet (26 to 36 meters) Suction x Delivery Size : 25 x 25 mm. Max. Flow Rate : 42 to 18 LPM.
Contents