How Do I Reset My Pats System?

Enter Security Access on the PATS control function module. Select “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Cycle key 1 to OFF, then RUN, and back to OFF. Cycle key 2 to RUN.

How do I reset my Ford anti-theft?

Key

1. Insert the key into the driver’s side door lock.
2. Turn the key once, but not all the way to unlock the door. Leave the key in this position for 40-60 seconds.
3. Do this again, but turn the key in the opposite direction.
4. Remove the key from the door, get into your Ford, and start the engine. The system should be reset.

How do I reprogram my Ford Pats?

Programming A PATS Key Yourself

1. You need to have one original key for your Ford.
2. You’ll need a new PATS key cut to match your ignition switch.
3. Start by putting the original key into the ignition.
4. Turn the ignition to ON, but don’t start the car.
5. Within 10 seconds, insert the new key, and turn the ignition to ON.

How do I reset my Securilock passive anti-theft system?

Simply put the original key in the ignition, turn to ON or RUN and wait for 20 seconds. Then turn the key off and start vehicle.

Can you reset anti-theft system?

If it is no longer blinking, turn the key to the “off” position and let your car sit for a couple of minutes. This allows the system to fully reset itself, or your car won’t start.

What triggers Ford anti-theft system?

The system arms when you lock your vehicle. When armed, the alarm is triggered in any of the following ways: If someone opens a door, the liftgate or the hood without a valid key or remote control. If you switch your vehicle on without a correctly coded key.

How long does it take for the anti-theft system to reset?

Leave the key there for 15 minutes; it doesn’t always take that long, but it can. After that time, check to see if the anti-theft light has gone out, if one was lit up. Turn the key backward two places to the Lock position, then wait three more minutes.

How do I reprogram my Ford keyless entry without a factory code?

Call Your Ford Dealer
This is technically the only way to reset your Ford’s keyless entry system without the factory code. Of course, you’ll need to provide proof of ownership for security purposes.

How do you reprogram a Ford transponder chip key?

Turn the ignition off and remove the first coded key from the ignition. After three seconds, but within ten seconds of turning off the ignition, insert the second previously coded key. Turn the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.

How do I reset my keyless Ford?

Resetting Your Ford Keyless Entry

1. Enter the factory-set five-digit code.
2. Press and release 1•2 on the keypad within five seconds.
3. Press and hold 1•2 for two seconds. You must do this within five seconds of completing step 2.
4. All personal codes should now be erased and only the factory-set five-digit code will work.

How do I get my car out of security mode?

After inserting the key into the driver’s door lock, turn the key to unlock, lock and then lock position again. Then, turn it again to the unlock position and the alarm is likely to be disabled now. Run the car for at least 10 minutes after cranking the engine to allow the car to reset the alarm.

How do I turn off anti-theft mode?

In order to deactivate the anti-theft system, car owners must press the unlock button located on the remote key. So it is suggested to use the key to unlock the door, then change the switch of ignition to “on” position.

Can a PATS system be bypassed?

In general, it’s better to disable or bypass PATS rather than pay someone to take it out of your car, but again this comes down to preference. To remove PATS from a Ford Mustang/vehicle, you need to have the transponder removed and its electronic chip taken out, which can be a tedious process.

How do you reset ignition switch?

How do I reprogram or reset a new ignition cylinder with key

1. turn key to ON for 10 minutes 30 seconds.
2. turn key to OFF for about 10 seconds.
3. back to ON for 10 min 30 sec.
4. back to OFF for about 10 seconds.
5. On for 10:30.
6. OFF for about 10 seconds.
7. ON.
8. Start the engine.

How do I disarm my Ford anti-theft system?

Disarming the Alarm
Use a key in the driver’s door to unlock the vehicle, then switch the ignition on within 12 seconds.

How do I turn off anti-theft without key fob?

Ways to stop a car alarm without a keyfob

1. Check your owner’s manual. Every vehicle is different.
2. Lock your doors.
3. Turn the car on.
4. Turn the ignition to on and wait.
5. Pull the fuse for the alarm.
6. Pull the wires for your alarm.
7. Disconnect the battery.

Can thieves bypass immobilizer?

‘Relay theft’ works against cars that have keyless entry and start systems. This is when the thief uses a device that can copy the code sent out by a driver’s car key and then replicates it to fool the vehicle that the key is present. This allows the thief to bypass the immobiliser and start up the vehicle.

How much does it cost to reset anti-theft system?

Labor costs are estimated between $104 and $132 while parts are priced at $315. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed. This range is an average across all vehicles on the road.

Is there a master code for Ford keyless entry?

The code is on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also program up to five of your own five-digit personal entry codes. Enter the factory-set five-digit code.

What is the Ford 5 digit factory code?

Look for the factory code.
The 5 digit security code is usually in the glove department if you have not moved the owner’s wallet card. The 5 digit code can also be found on years 2011- 2018 on a white label inside passenger side fuse box, it will be the 5 numbers you need, followed by a letter.

How do I program a chip key for myself?

Programming a Single Key

1. Insert the key into the ignition, and turn it to the on position.
2. Leave the key in this position for 10 minutes and 30 seconds, and then turn it off.
3. Turn the key back on, and wait for additional 10 minutes and 30 seconds before turning it off again.
4. Repeat the process for a third time.