How Do I Reset My 2016 Sync Mustang?

The system reset does not delete any data you have stored.

To reset the system:

1. Simultaneously press and hold the Seek up and the audio unit Power buttons until the screen goes black.
2. Wait three minutes to allow the system to complete the reset.
3. Press the audio unit Power button to switch the system on.

How do I resync my Ford Sync?

1. On your phone, go to SETTINGS in the menu>
2. Find the BLUETOOTH menu option and touch to open it>
3. Once SYNC appears, touch the GEAR (right side of screen)>
4. You will see UNPAIR. Touch UNPAIR and the sync will be removed from phone>
5. Take out the battery, wait 30 seconds, replace, and power phone back on.

What do I do if my Ford Sync is not working?

Power off your phone and remove the battery, if possible. Turn the phone back on. Verify that your phone automatically connects to SYNC after performing a key cycle.
Manually connect SYNC with the phone.

1. Touch Phone.
2. Press Settings.
3. Tap Bluetooth Devices.
4. Select your phone.
5. Touch Connect.

Will disconnecting battery reset Ford Sync?

To perform a Hard Reset: With the ignition OFF, disconnect the power to the SYNC module buy either disconnecting the vehicle battery or the large 54 pin connector at the back of the module. Reconnect the power after 30 seconds.

How do you reset the sync on a Mustang?

Press Settings on your vehicle’s SYNC screen. Choose General. Scroll down and press Master Reset. A message confirming that all system settings will be erased and reset to factory defaults will appear.

How do you hard reset a sync module?

Use a small object or fingernail to press the reset button for 5 seconds. You will see a flash of red and then after 15 seconds a blinking blue light and solid green light appear at the front of the Sync Module. The Sync Module is ready to be added through the Blink app.

How do I restore auto sync?

Step 1: Tap the menu in the top left to see your preferences and other options. Step 2: Tap on the Manage Auto Sync text to open auto sync preferences on your device. Step 3: Tap the green Turn Auto Sync On button to enable auto sync. Step 4: You can now see that auto sync is enabled on this screen.

How do I manually update sync?

Manual Updating via USB

1. Log into your SYNC account.
2. Go to the SYNC® Software Updates page to check for a notification that says “You have an update available.”
3. Insert your empty USB flash drive into the computer and click “Start Download Process” on your browser.

What does Reset Sync do?

The “Reset Sync” button is located right below the current status of the sync and if there are any errors. The feature itself is primarily a reset on the back end to clear out any stored errors that would be retried or data used for a delta sync.

How do I resolve Sync issues?

Resolving sync conflicts

1. Open the Start Menu and select Control Panel. Windows 10.
2. Open Sync Center. Category View.
3. Select View Sync Conflicts from the menu on the left.
4. Select a conflict from the list.
5. Click Resolve.
6. Select file version for sync.

What causes out of Sync?

Old audio drivers, inappropriate sound settings, or a slow internet connection can all be the cause. However, sometimes there’s nothing wrong with your computer or browser, and it’s the streaming service you’re using that causes the audio-video problem.

How do I get my Sync to work?

Start your engine and ensure your radio is on. Access the Settings app on your smart device and enable Bluetooth as visible. Press “Phone” on your Ford SYNC® settings, and then “Add” to pair. SYNC® will prompt you to “Search for SYNC on your device”.

Does unplugging the battery reset the car?

On some older cars, disconnecting the battery will reset the system but in most new cars it does nothing, except potentially reset the clock and radio station presets.

Does unplugging the battery reset codes?

Leaving the battery disconnected for about 15 minutes will ensure the vehicle systems will completely reset when you reconnect the battery. Secure the negative cable back to the terminal and cover it with the cap (if applicable). Disconnecting the battery will clear the error codes and reset the check engine light.

Do you have to reset car computer after replacing battery?

Most ECUs are self-learning and should reset themselves after learning that a new battery has been installed. If you’re stuck, go to a mechanic for diagnostic assistance.

How do I force a factory reset?

Using the volume buttons, scroll down to “Recovery,” then press the power button. If the only option in the menu is “No Command,” press and hold the power button, then press volume up. Either way, you’ll end up in the reset menu. Here, use the volume down button to scroll to the “Wipe data/factory reset” option.

Does a factory reset delete everything?

A factory data reset erases your data from the phone. While data stored in your Google Account can be restored, all apps and their data will be uninstalled. To be ready to restore your data, make sure that it’s in your Google Account. Learn how to back up your data.

How do I reset my Ford Sync when the screen is black?

Your SYNC 3 system may exhibit a blank or black screen.
Perform a soft reset.

1. Select Radio.
2. Hold the Power button (center of the volume knob) + the Right-Seek button at the same time for approximately five seconds.
3. The display will indicate when the module is resetting. You may then release the buttons.

How do I reset my touchscreen on my car?

Clean your touchscreen. Reboot the touchscreen by turning it off and back on again. Recalibrate the screen from the settings menu. Perform a factory reset.

How do I reset my Ford PCM?

If only the PCM is being replaced on a PATS control function type A or D vehicle, no relearn is required (please refer to the Ford PATS chart to determine PATS type). Simply put the original key in the ignition, turn to ON or RUN and wait for 20 seconds. Then turn the key off and start vehicle.

Where is reset button on Sync module?

The reset button is located on the right-hand side of the Sync Module next to the USB port. Please note that this could take between 15-30 seconds. This will cause the Sync Module to reboot into setup mode.