How Wide Is A Mustang 8.8 Rear End?
59 11/44.
How To Spot, Build, And Swap In the Ford 8.8 Mustang Rearend.
Vehicle Application | Axle Width (inches) |
---|---|
’86-’93 Ford Mustang 8.8 | 59 11/44 |
FORD | |
’65-’66 Mustang | 57 11/44 |
’67-’70 Mustang 8.0 | 59 51/48 |
How wide is an 8.8 rear end?
7] From the factory, 8.8s use 1330- or 1310-series U-joints. This is the companion flange where the yoke bolts. The 1330 has a 3316-inch width for the U-joint, and the 1310 has a 358-inch width. The 1330 is usually found in Ford trucks.
How wide is a Ford 8 inch rear end?
The Ford 8-inch housing has a center casing roughly 11 inches wide. Most flange-to-flange assemblies are between 56 and 62 inches wide; you can check the axle length chart we have available at www.hemmings.com/parts-locator for specific measurements for your body style.
How wide is a 2006 Mustang rear end?
From 1986-2010, the Ford Mustang 8.8” rear end would be used for all V8 Mustangs, and the Ford 7.5” rear end was installed into all 4-cylinder (2.3L) and V6 Mustangs (3.8L).
How wide is Mustang rear end?
Most rear axles are described by their ring-gear diameters, with larger being better. A Ford 9-inch has a ring-gear diameter of, you guessed it, 9 inches closely followed by the 12-bolt at 8.875, with the Mustang rear at 8.80 inches.
How wide is a factory g body rear end?
58 inches
Products specifications
Vehicle Fitment | 78-87 GM G-body vehicles (Malibu, Monte Carlo, Monte Carlo SS, El Camino, Regal, Grand National, Cutlass, Cutlass 442, Cutlass Salon, Grand Prix, Caballerro and Station Wagons) |
---|---|
Brake Space | 2.5 inch axle standoff |
Width | 58 inches (between wheel mounting surfaces) |
How wide is a Ford 9-inch rear end?
The 9” rear axle was manufactured in seven different housing widths, from 57-1/4” to 69-1/4” wide, any of which may be ideal for a particular chassis.
How wide is a 2005 Mustang rear end?
Track width, front/rear 61.9 in. / 62.5 in. 62.4 in. / 63.0 in.
What is the ratio of a Ford 8.8 rear end?
Ford 8.8 Inch 3.55-5.13 Ratio.
How wide is a GM 10 bolt rear end?
Many times, if you locate a 10-bolt rearend, it’s usually a 7.5-inch unit. These have been around since 1975, and were installed under cars, small trucks, and vans up to the 2005 model year.
What is a ghost cam tune?
Ghost Cam tunes utilize the Mustang’s Twin Independent Variable Cam Timing (TiVCT) to make the engine sound and feel race-ready.
How do I know the width of my axle?
It’s best to remove your tire assemblies off your axles when measuring your hub face. Hook your tape measure on the outside of the hub where your rim touches your hub. Measure across your axle to the exact same spot on the other side. Do not measure to the back side of your hub.
How wide is a 1970 Mustang rear end?
Currie® Ford 9-inch rearends for 1967 thru 1970 Mustang and Cougar, provide a direct bolt-in solution for those looking to upgrade the rearend of their classic muscle car or restomod build.
How do I identify a Ford 8.8 rear end?
You can identify the Ford 8.8-inch rear by its rear cover. It has a thin metal or plastic 10-bolt cover, and the bolts are 7/16-inch thread. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The 8.8-inch pinion shaft is 15/8 inches and has 30 splines.
What Fords had a 9-inch rear end?
Common applications
- 1957-1986 Ford F-100 & F-150.
- 1958-1960 Edsel (All series including Wagons)
- 1976-1980 Ford Granada.
- 1976-1979 Lincoln Versallies.
- 1957-1970 Ford Fairlane.
- 1957-1971 Ford Thunderbird.
- 1964 1/2-1973 Ford Mustang.
- 1966-1983 Ford Bronco.
What is the rarest G-body car?
Nine Rarest GM G-Bodies
- 1988 Chevy Monte Carlo (all) quantity: 30,174.
- 1988 Oldsmobile Cutlass Supreme “Classic” (all) quantity: 27,678.
- 1987 Chevy Monte Carlo SS Aerocoupe quantity: 6,052.
- 1986 Oldsmobile Cutlass 4-4-2 quantity: 3,500.
- 1983 Hurst Olds Cutlass quantity: 3,500.
- 1982 Hurst Olds Cutlass quantity: 3,001.
What does the G in G-body stand for?
The General Motors G platform (also called G-body) was an automobile platform designation used for mid-sized rear-wheel drive cars. It made its first appearance from the 1969 to 1972 model years, adapted from GM’s A-body, and reappeared from 1982 to 1988.
How wide is a C4 Corvette rear end?
An 84 to 89 C4 rear axle is 62.5 inches from tire-mount surface to tire-mount surface. The 90 to 96 axles are -inch wider.
How wide is a Ford 9-inch rearend?
Many street stock circle track and drag racers prefer the 9-inch rear found in ’66-’70 full size Fords and Mercurys, ’71-’72 Lincolns, and ’68-’72 F100 Ford trucks because it has 31-spline axles, large ball-type axle bearings and a 61″ overall width (measured from drum face to drum face).
How wide is a Ford 9-inch axle?
These axles are 65 inches wide from wheel mounting surface to wheel mounting surface (a 68-inch-wide E-series van version is also common), feature the legendary 9-inch diameter ring gear, large Timken set 20 axle bearings, semi-floating 28- or 31-spline axleshafts, drum brakes, and a 5-on-5.5 lug pattern.
Why is the Ford 9-inch so strong?
The 9-inch Ford Rearend is the Strongest Rearend Out There—It’s All Due to “Hypoid Distance” 1] The 9-inch Ford has no differential case gear-ratio range restrictions; one differential accepts all gear ratios from the 2s through the 6s.
Contents