What Settings Should My Fender Amp Be On?
Fender amps just do reverb really well. Try going with a low bass, high treble setting (similar to the magic six) with the reverb knob on seven or eight. Your higher notes will have a nice “chime” to them and your low-end notes should come out clean without becoming too muddled.
What are the best settings for a guitar amp?
Dialing in the perfect tone to go with high-saturation gain levels and metal riffs.
- GUITAR: VOLUME: MAX / TONE: MAX / SELECTOR: MIDDLE OR BRIDGE.
- AMP: BASS: 8 / MIDS: 4 / TREBLE: 4 / GAIN: 10 (or pedal) / REVERB: OFF.
- DISTORTION PEDAL: LEVEL: AMP VOLUME / DRIVE: 75% / BASS: 6-8 / TREBLE: 3-5.
What settings did Kurt Cobain use on his amp?
Kurt Cobain used a range of tones depending on the songs he was playing, but generally, he set his amp settings at 7-8 for the treble and mids and the bass around 5. He generally set his distortion high for choruses (8-10) unless a pedal was used.
What amp settings did Jimi Hendrix use?
Answer: Jimi Hendrix’s amp settings depended greatly on the song he was performing, but generally, he has the bass at around 4, the mids at 8, the treble at 6, and the gain at 4 or 5.
How can I make my amp sound better?
How to Make a Guitar Amp Sound Better
- Understand your amp.
- Ease off on the gain.
- Boost your mids.
- Placement is key.
- Consider adding pedals.
- Care for your cables.
- Select the right pickup.
What amp settings did Eddie Van Halen use?
In summary, the main gear Eddie Van Halen uses and main pedals Eddie used were a phaser, ideally a Phase 90 and a delay pedal, ideally an Echoplex all put through a 5150 amplifier.
What amp settings does Eric Clapton use?
The amp settings were: presence 3; bass and middle 1 o’clock; treble 8; and volume just under 9. The strings he used were Ernie Balls . 010-. 046.
What amp did Van Halen use?
This tone is pretty simple, Eddie Van Halen used his legendary Marshall Plexi amplifier famously cranked to the hilt with every knob turned up to 10 (or 11!) and his iconic Frankenstein guitar with the single humbucker in the bridge. The reverb and room mic effects mixed in also have an influence on this recording.
What amp did Foo Fighters use?
What amps do Foo Fighters use? Foo Fighters primarily use Mesa/Boogie amps for driven tones and a Vox AC30 for clean tones.
What amp did ACDC use?
Amps. The guitar amp is a big part of where ACDC get their ‘sound’ from. Essentially, they just crank up Marshall Plexi amps which are surprisingly not high gain amps. But when turned up that loud, they’ll break up the speakers for that classic rock sound.
What amps do Metallica use?
What amps do Metallica use? Metallica are well known for using Mesa/ Boogie amplifiers such as the Mark IIC. James is also known to play the Roland JC-120 for his clean tones. Kirk also has a signature line of amps with Randall.
What amp settings does Metallica use?
Metallica Load Album Amp Settings
Gain: 2. Treble: 6. Mids: 2. Bass: 6.
How do I make my amp tone crunchy?
Although you can get a crunch tone with pedals, it came about by running an amp hard and pushing it past it’s happy clean sound. The first way to achieve a crunch tone is by pushing the amp with pedals. A boost pedal does just what the name implies. It boosts the signal coming from the guitar.
What happens if amps are too high?
There should be no upper limit for how much amps a power supply provides. It only draws as much as it needs when operating normally. If you give it a power supply capable of 50A, you can turn an annoying short circuit into a catastrophic incident with sparks and burning electronics and flying shards of plastic.
Should amp input level be high or low?
Using the High Level input is always the best option. Using the High Level Input, instead of the Low Level Input, and connecting to the speaker output terminals of your amplifier is one of the unique secrets of REL’s success.
What is gain and level on an amp?
The differences between these two terms might seem simple, though people often complicate the difference. To make it simple for you, gain is the level of your audio going into a system while the volume is the level going out of your system.
What amp does Slipknot use?
Slipknot use a variety of amps, with Jim Root primarily using Orange amps such as the Dark Terror and Rockerverb, whilst Mick Thomson mainly uses a Rivera KR7.
How do I make my guitar sound Brown?
CREATING THE BROWN SOUND
Simply take a humbucker loaded guitar, plug into a British El-34-based Plexi amp and go.
What amp settings did Stevie Ray Vaughan use?
Clean Amp Settings
- Presence: 6.
- Treble: 9.
- Mid: 6-8.
- Bass: 5-6.
- Gain: 3.
- Volume: 5.
What amplifier did paul McCartney use?
What a lot of people do not know is that the 1964 6G6-B Bassman was actually the most recorded amplifier by The Beatles. The amp was first used by Paul McCartney as his main bass amp from 1965 to mid 1967 (he did use a Vox during this time but not as much as the Bassman).
What is the best amp settings for rock?
Rock Music Amp Settings
- Gain: 6-7.
- Bass: 5.
- Treble: 4.
- Mids: 7.
Contents